Copper Sand Cast Alloy (UNS C89844) – Mechanical Properties
Copper UNS C89844 has a copper content of not less than 83%.
The following table shows the mechanical properties of UNS C89844 sand cast alloy as a function of heat treatment.
| Melunakkan | Tensile Str. | Yield Str. | Elong. |
|---|---|---|---|
| M01 | 234MPa (34ksi) | 103MPa (15ksi) | 30% |
The chemical composition of UNS C89844 copper alloy is outlined in the following table.
| Cu% | Pb% | Sn% | Zn% | Fe% | P% | Ni%1 | Al% | Dua% | S% | Sb% | Dan% |
|---|---|---|---|---|---|---|---|---|---|---|---|
Komposisi kimia disediakan oleh CDA 1Ni value includes Co. Note: Cu + sum of named elements, 99.3% min. Single values represent maximums. | |||||||||||
| 83.00- 86.00 | 0.20 | 3.00- 5.00 | 7.00- 10.00 | 0.30 | 00,05 | 1,00 | 0.005 | 2.00- 4.00 | 0.08 | 0.25 | 0.005 |
C89844 Product description: Bismuth tin bronze
Solids: 1/2″ to 10″ O.D.
Tubes: 1 1/8″ to 9″ O.D.*
Rectangles: Up to 15″
Standard lengths: 144″
Bentuk/Bentuk: setengah jadi, bentuk mill stock atau near-net, anode, bar stock, billet/bloom, kotak, heksa, pelat, profil atau bentuk struktur, batang datar/persegi panjang
Compliance: C89844 is compliant with key legislation including (1) Federal Safe Drinking Water Act – SDWA, (2) S. 3874 Federal Reduction of Lead in Drinking Water Act, (3) California AB1953, and (4) Vermont Act 193
*Konsultasikan dengan pabrik untuk mengetahui ketebalan dinding
Kegunaan yang khas
Plumbing: fittings/valves for potable water
Komposisi kimia
| Cu% | Pb% | Sn% | Zn% | Fe% | P% | Ni%1 | Al% | Dua% | S% | Sb% | Dan% |
|---|---|---|---|---|---|---|---|---|---|---|---|
Komposisi kimia disediakan oleh CDA 1Ni value includes Co. Note: Cu + sum of named elements, 99.3% min. Single values represent maximums. | |||||||||||
| 83.00- 86.00 | 0.20 | 3.00- 5.00 | 7.00- 10.00 | 0.30 | 00,05 | 1,00 | 0.005 | 2.00- 4.00 | 0.08 | 0.25 | 0.005 |
Kemampuan mesin
| Paduan tembaga UNS No. | Peringkat kemampuan mesin | Kepadatan (lb/in3 pada 68 °F) |
|---|---|---|
| C89844 | 70 | 0.31 |
Peralatan mekanis
| Kekuatan tarik, min | Kekuatan hasil, pada ekstensi 0,5% di bawah beban,, min | Perpanjangan, dalam 2 inci atau 50 mm min | Kekerasan Brinell (beban 500 kg) | Perkataan | ||
|---|---|---|---|---|---|---|
| ksi | MPa | ksi | MPa | % | tipikal BHN | |
| 28 | 193 | 13 | 90 | 5 | 55 | |
Properti fisik
Sifat fisik disediakan oleh CDA | |||||||||||
| Adat AS | Metrik | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Titik lebur – cair | 1850 °F | 1010 °C | |||||||||
| Titik lebur – solidus | 1550 °F | 853 °C | |||||||||
| Kepadatan | 0.310 lb/in3 at 68 °F | 8.58 gm/cm3 at 20 °C | |||||||||
| Berat jenis | 8.58 | 8.58 | |||||||||
| Konduktivitas listrik | 16.8% IACS at 68 °F | 0.095 MegaSiemens/cm at 20 °C | |||||||||
| Konduktivitas termal | 46.7 Btu/sq ft/ft hr/°F at 68 °F | 80.9 W/m at 20 °C | |||||||||
| Koefisien muai panas 68-392 | 10 · 10-6 per °F (68-392 °F) | 17.3 10-6 per °C (20-200 °C) | |||||||||
| di antaranya 06Cr19Ni10 umumnya berarti produksi standar Cina | 0.08 Btu/lb/°F at 68 °F | 335.2 J/kg at 20 °C | |||||||||
| Modulus elastisitas tegangan | 13000 ksi | 89622 MPa | |||||||||
Properti fabrikasi
Properti fabrikasi disediakan oleh CDA *Since brazing is performed within the hot-short range, strain must be avoided during brazing and cooling. | |||||||||||
| Teknik | Kesesuaian | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Pematerian | Bagus sekali | ||||||||||
| Brazing* | Bagus | ||||||||||
| Pengelasan oksiasetilen | Tidak direkomendasikan | ||||||||||
| Pengelasan busur terlindung gas | Tidak direkomendasikan | ||||||||||
| Pengelasan busur logam berlapis | Tidak direkomendasikan | ||||||||||
| Peringkat kemampuan mesin | 70 | ||||||||||
Sifat termal
Sifat termal disediakan oleh CDA *Temperature is measured in fahrenheit. **For stress relief, solution treatment and annealing – time is measured in hours/inch of thickness. For precipitation heat treatment – time is measured in hours. |
